VBA-4E4A-CB10-ZEJ/E0J-FL AS-Interface printed circuit board module

Ventajas clave de un vistazo

Integrated communication monitoring function
Outputs short-circuit and overload proof
Supply of the inputs and the outputs from AS-Interface
Function display for bus, inputs and outputs
Connection via lead

Product photo: AS-Interface printed circuit board module VBA-4E4A-CB10-ZEJ/E0J-FL

Dimensions: AS-Interface printed circuit board module VBA-4E4A-CB10-ZEJ/E0J-FL

Nota

Todos los documentos relacionados con los productos, como certificados, declaraciones de conformidad, etc., que se emitieron antes de la conversión con el nombre de Pepperl+Fuchs GmbH o Pepperl+Fuchs AG también se aplican a Pepperl+Fuchs SE.

ES

ES
EN
DE
FR

Hoja de datos Función Clasificación Product Documentation Homologaciones

Datos técnicos de VBA-4E4A-CB10-ZEJ/E0J-FL

Printed circuit board module, 4 inputs/4 outputs

Node type		A/B node
AS-Interface specification		V3.0
Required gateway specification		≥ V3.0
UL File Number		E223772
MTBF		267 a

LED FAULT		error display; LED red red: communication error or address is 0 red flashing: overload of outputs
LED PWR		AS-Interface voltage; green LED green: voltage OK flashing green: address 0
LED IN		switching state (input); 4 LED yellow
LED OUT		Switching state (output); 4 LED yellow

Rated operating voltage	U_e	26.5 ... 31.6 V from AS-Interface (PELV)
Rated operating current	I_e	≤ 40 mA (without inputs/outputs)/max. 160 mA
Protection class		III
Surge protection		U_e: overvoltage category II, safe isolated power supplies (PELV)

Number/Type

4 inputs for mechanical contacts or 3-wire sensors (PNP), DC

Supply

from AS-Interface

Voltage

12 ... 31 V

Current loading capacity

≤ 100 mA Total including output current, overload and short-circuit proof

Input current

≤ 4 mA (limited internally)

Switching point

0 (unattenuated)		≤ 0.15 mA
1 (attenuated)		≥ 1.3 mA

Signal delay

< 1 ms (input/AS-Interface)

Number/Type		4 electronic outputs, NPN, overload proof and short-circuit proof
Supply		from AS-Interface
Voltage		12 ... 31 V
Current		≤ 100 mA per output, ≤ 100 mA in total, including input supply
Usage category		DC-1 "general use" (ohmic and weak inductive loads in accordance with IEC 60947)

Electromagnetic compatibility

Directive 2014/30/EU

EN 62026-2:2013

Degree of protection		EN 60529:2000
Fieldbus standard		EN 62026-2:2013
Emitted interference		EN 61000-6-4:2007
AS-Interface		EN 62026-2:2013
Noise immunity		EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013

Profile

S-7.A.7

IO code

7

ID code

A

ID1 code

7

ID2 code

7

Data bits (function via AS-Interface)

InputOutput

D0		IN1 OUT1
D1		IN2 OUT2
D2		IN3 OUT3
D3		IN4 OUT4

Parameter bits (programmable via AS-i)

function

P0		not used
P1		Input filter P1 = 0 input filter on, pulse suppression ≤ 2 ms P1 = 1 input filter off (default settings)
P2		Synchronous mode P2 = 0 synchronous mode on P2 = 1 synchronous mode off (default settings)
P3		not used

UL approval

Protection class IP20 is not included in the UL approval. The protection class is tested by Pepperl+Fuchs.

Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-25 ... 85 °C (-13 ... 185 °F)
Relative humidity		85 % , noncondensing
Climatic conditions		For indoor use only
Altitude		≤ 5000 m above MSL
Shock and impact resistance		30 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks
Vibration resistance		0.35 mm 10 ... 57 Hz , 5 g, 57 Hz ... 150 Hz, 10 cycles
Pollution degree		2

Degree of protection

IP20 according to EN 60529

Connection

200 mm, PVC cable 0.5 mm²

Material

Housing

Polyamide hot-melt adhesive

Mass

33 g

Dimensions

Height		10 mm
Width		36 mm
Length		39.5 mm

Note

This device is maintenance-free. If the device is used in a manner not specified by the manufaturer, the protection provided by the device may be impaired.

Notas generales