OGR4000-R305-2EP-IO-V1 Retroreflective area sensor

Key Benefits at a Glance

Retroreflective area sensor with five light beams in a standard photoelectric sensor enclosure
Bright, highly visible transmitter beams guarantee convenient alignment of the sensor
Reliable detection of all surfaces irrespective of the object texture
Reliable small part detection for very flat objects with an irregular shape
Constant object detection from 2 mm within the entire detection area

Product photo: Retroreflective area sensor OGR4000-R305-2EP-IO-V1

Dimensions: Retroreflective area sensor OGR4000-R305-2EP-IO-V1

Note

All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Datasheet Function Classification Product Documentation Design / Simulation Approvals Software

Technical data of OGR4000-R305-2EP-IO-V1

Retroreflective area sensor, red light, max. detection range 4 m, light field height 60 mm, IO-Link interface, 2 push-pull outputs, M12 plug

Effective detection range		Standard mode: 0 ... 4 m High resolution: 0 ... 2 m
Reflector distance		0.2 ... 4 m H85-2 reflector
Threshold detection range		4 m
Sensing range		see table
Reference target		H85-2 reflector
Light source		LED
Light type		modulated visible red light
LED risk group labelling		exempt group
Field height		60 mm
Field width		12 mm
Object size		Minimum 2 mm, 3 mm, 5 mm, 8 mm, 10 mm; position-independent detection within detection range
Number of beams		5
Opening angle		+/- 2 °
Ambient light limit		EN 60947-5-2
Resolution		see table

MTTF_d		674 a
Mission Time (T_M)		20 a
Diagnostic Coverage (DC)		0 %

Operation indicator		LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode
Function indicator		Yellow LED: Permanently on: light path clear Permanently off: object detected Flashing (8 Hz) - end of compensation
Control elements		Teach-In key
Control elements		5-step rotary switch for operating modes selection

Operating voltage	U_B	10 ... 30 V DC IO-Link mode: 18 ... 30 V DC
Ripple		max. 10 %
No-load supply current	I₀	< 35 mA at 24 V supply voltage
Protection class		III

Interface type		IO-Link
IO-Link revision		1.1
Device profile		Identification and Diagnosis - I&D Smart Sensor - SSP 2.1
Process data		Input 8 Bit - switching signal 1 Bit - stability alarm 1 Bit - measurement value 6 Bit Output 2 Bit - sensor control function 1 Bit - evaluation control function 1 Bit
Vendor ID		1 (0x0001)
Device ID		0x101001 (1052673)
Transfer rate		COM2 (38.4 kBit/s)
Min. cycle time		2.3 ms
SIO mode support		yes
Compatible master port type		Class A , Class B (use 3-pole adapter or 3-wire cable)

Switching type		The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: NPN normally open / dark-on, PNP normally closed / light-on, IO-Link /Q - Pin2: NPN normally closed / light-on, PNP normally open / dark-on
Signal output		2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected, overvoltage protected
Switching voltage		max. 30 V DC
Switching current		max. 100 mA
Voltage drop	U_d	≤ 1.5 V DC
Switching frequency	f	Standard mode: 500 Hz , High resolution: 250 Hz
Response time		Standard mode: 1 ms , High resolution: 2 ms

Communication interface		IEC 61131-9 / IO-Link V1.1.4
Product standard		EN 60947-5-2

UL approval		E87056 , cULus Listed , class 2 power supply , type rating 1
CCC approval		CCC approval / marking not required for products rated ≤36 V

Ambient temperature		-40 ... 60 °C (-40 ... 140 °F) The permissible minimum ambient temperature during teach-in is -30 °C. The permissible temperature change after teach-in is ±20 K.
Storage temperature		-40 ... 70 °C (-40 ... 158 °F)

Degree of protection

IP67

Connection

4-pin, M12 x 1 connector, 90° rotatable

Material

Housing		PC (Polycarbonate)
Optical face		Plastic pane

Mass

94 g

Dimensions

Height		89 mm
Width		25.8 mm
Depth		59.5 mm

General Notes